Flexible Heavy-Duty Coating

• ENVIRONMENTALLY FRIENDLY - Liquid Rubber Colour Waterproof Sealant is water based, containing no Solvents or VOC's. This means it's safe to use indoors and outdoors with no special breathing apparatus like solvenated products need. You're safe, your children are safe and your pets are safe. We believe you should have a choice in purchasing high quality products that are safe for you and the environment
• USED FOR: Flat Roofs, Metal Roofs, Sloped Roofs, Planter Boxes, Foundations, Sheds, Basements, Metal, Wood, Concrete and more...
• See DIY APPLICATIONS for more specific info
• EASY TO APPLY - Basically just like painting except you use heavy coats to build up your waterproof membrane. Open the container and start using. You can close the container and use later if you have left over material. No pot life or working time like 2 component products. Apply by Brush, Roller or Good Quality Paint Sprayer
• HIGHLY FLEXIBLE - UV Stable - Final membrane has over 1000% Elongation and the Sun will not degrade the product.
• FOR A BULLETPROOF SYSTEM - Bridge joints, seams, vents, gaps, protrusions…. With LIQUID RUBBER SEAM TAPE or LIQUID RUBBER GEO-TEXTILE where possible movement may occur.

Flat/Ponding Surface

Apply a minimum final thickness of 1 gallon per 15 sq ft (1.4 sq/m). It should require around 4-5 heavy coats to achieve a 60-80 mil  (1.5-2.0mm) (DFT) membrane.

Vertical Surfaces

Apply a minimum final thickness of 1 gallon per 25 sq ft (2.3 sq/m). It should require around 2-3 heavy coats to achieve a 30 mil  (0.76mm) (DFT) membrane.

Tips

• Avoid hot, direct, intense sun when applying.  Mornings and Evenings are best if it's blistering hot
• Product stays soft, flexible and may have some tackiness, not meant as a constant walking surface
• Apply next heavy coat when it's dry to touch (typically 6-8 hours), make sure there is no uncured material underneath.  Tacky is ok
• Generally you can apply 1-2 coats per day
• Apply all material until you use up the required amount
• Do not combine Black products with Coloured products, use one or the other
• For larger areas, pour out and spread around with a broom, roller or squeegee
• If corrosion/rust is present, use a water-based rust primer
• Use EPDM/TPO Primer for EPDM/TPO substrates.  Use Multi-Purpose Primer for PVC and Concrete Surfaces
• Apply above 10C/50F
• Curing time depends on temperature, humidity and airflow
• Apply next coat(s) as soon as possible not allowing extended time between if possible
• Safe for Fish and Plants
• Do not apply later in the day if Dew is forecast.

• Gazebo Roof Case Study
• Residential Metal Roof Case Study
• Residential Home Planter Box

Liquid Rubber Coloured Waterproof Sealant Data Sheet

Liquid Rubber Coloured Waterproof Sealant Safety Data Sheet

Flexible Heavy-Duty Coating

• ENVIRONMENTALLY FRIENDLY - Liquid Rubber Waterproof Sealant is water based, containing no Solvents or VOC's. This means it's safe to use indoors and outdoors with no special breathing apparatus like solvenated products need. You're safe, your children are safe and your pets are safe. We believe you should have a choice in purchasing high quality products that are safe for you and the environment
• USED FOR: All Roofs, Gutters, Planter Boxes, Foundations, Basements, Ponds, Sheds, Mobile Homes, Metal, Wood, Concrete and more
• See DIY APPLICATIONS for more specific info
• EASY TO APPLY - Basically just like painting except you use heavy coats to build up your waterproof membrane. Open the container and start using. You can close the container and use later if you have left over material. No pot life or working time like 2 component products. Apply by Brush, Roller or High Quality Piston Paint Sprayer
• HIGHLY FLEXIBLE - UV Stable - Final membrane has over 1000% Elongation and the Sun will not degrade the product.
• FOR A BULLETPROOF SYSTEM - Bridge joints, seams, vents, gaps, protrusions…. With LIQUID RUBBER SEAM TAPE or LIQUID RUBBER GEO-TEXTILE where possible movement may occur

Coverage

Flat/Ponding Surface

Apply a minimum final thickness of 1 gallon per 15 sq ft (1.4 sq/m). It should require around 4-5 heavy coats to achieve a 60-80 mil  (1.5-2.0mm) (DFT) membrane.

Vertical Surfaces

Apply a minimum final thickness of 1 gallon per 30 sq ft (2.8 sq/m). It should require around 3-4 heavy coats to achieve a 30 mil  (0.76mm) (DFT) membrane.
 

Tips

• Avoid hot, direct, intense sun when applying.  Mornings and Evenings are best if it's blistering hot
• Product stays soft, flexible and may have some tackiness, not meant as a constant walking surface
• Apply next heavy coat when it's dry to touch (typically 12-24 hours), make sure there is no uncured material underneath.  Tacky is ok
• Generally you can apply 1-2 heavy coats per day
• Apply all material until you use up the required amount
• Do not combine Black products with Coloured products, use one or the other
• For larger areas, pour out and spread around with a broom, roller or squeegee
• If corrosion/rust is present, use Liquid Rubber MetalSafe Sealant
• Use EPDM Primer for EPDM substrates.  Use Multi-Purpose Primer for PVC and Concrete Surfaces
• Apply above 5C/40F
• Curing time depends on temperature, humidity and airflow
• Apply next coat(s) as soon as possible not allowing extended time between if possible
• Safe for Fish and Plants
• Membrane will turn Brown in ponding situations due to surfactants.  Will dissipate over time as the water cycles
• Do not apply later in the day if Dew is forecast

• Patio Over Wine Room
• Gazebo Roof
• Residential Metal Roof
• Under Patio Paver Deck
• Corner Gutter Repair
• Gutter Repair

Liquid Rubber Waterproof Sealant Data Sheet

Liquid Rubber Waterproof Sealant Safety Data Sheet

ASI-55 Hybrid Sealant & Adhesive 4-PK

ASI 55 Industrial & Construction Hybrid Sealant & Adhesive is a one-part, moisture cure adhesive that cures to form a permanent, durable rubber for use in various adhesive & sealant applications. ASI 55 has been formulated to offer exceptional adhesion and green strength for adhesive applications and excellent UV resistance and long-term properties for sealant applications. ASI 55 is a non-slump sealant and can be applied to vertical or overhead surfaces without flowing or sagging. 

ASI 55 is 100% solids and has a very low odor which makes it ideal for confined or occupied work spaces. ASI 55 is paintable and non-corrosive with a very broad adhesion profile. ASI 55 Hybrid Sealant & Adhesive is an excellent alternative to polyurethane and solvent based adhesive/sealant chemistries. 
 

Coverage

Approximately 24 linear feet at ¼” diameter bead.

Tips

• Apply to clean, dry surface that is free of dirt, silicone, loose paint, rust, oil, grease, coal tar, or other contaminants.
• Apply when temperature is above 5˚C/41˚F and rising.
• Use Liquid Rubber Deck and Patio Cleaner to prep wood.
• Avoid hot, direct, intense sun when applying.  Mornings and Evenings are best if it's blistering hot.
• Curing time depends on temperature, humidity and airflow.
• Do not apply in wet conditions (including fog and dew) or if rain is forecasted within 24 hours.
• Tape off the area to ensure a clean and neat application. Pull tape as soon possible.
• Tool before skin formation.
• Make sure what you’re coating is at least 5 degrees above the dew point of the environment you are coating in. (See technical specs for more details)
• For best results remove existing paints/coatings and apply directly to the substrate. (Some paints and coatings will not be compatible. Loose/flaky paint may be an indication that the existing paint/coating is not well bonded and therefore your Liquid Rubber solution may fail if applied over it instead of directly to the substrate. Oil based paints, enamels, epoxies, powder coats can be difficult to bond to. Contact your Liquid Rubber technical representative for further direction.)
• Wait 24 before painting.
• Full strength is achieved in 7 days.
• Do not allow to freeze.

Technical Data Sheet - ASI-55 Hybrid Sealant & Adhesive

Safety Data Sheet - ASI-55 Hybrid Sealant & Adhesive

Flexible Corrosion Coating

• Ultrahigh corrosion protection
• Can be applied directly over lightly rusted surfaces
• Creates a long lasting waterproof membrane
• Excellent adhesion, chemical and UV resistance
• Resists cracking, chipping, impact and abrasion
• Resistant to freeze/thaw cycles
• Withstands extreme hot and cold environments
• Easy to apply roller, brush & spray equipment
• Available in BLACK ONLY

For Flat and Ponding Surfaces:

• Apply a minimum final thickness of 1 gallon per 15 sq ft (1.4 sq/m). It should require around 4-5 heavy coats to achieve a 60-80 mil. (1.5-2.0mm) (DFT) membrane.

For Vertical Surfaces:

• Apply a minimum final thickness of 1 gallon per 30 sq ft (2.8 sq/m). Apply 2-3 heavy coats to achieve a 30 mil. (0.76mm) (DFT) membrane.
   

• Apply using a 3/8 (10mm) roller, brush or appropriate paint sprayer.
• Apply to dry surface that is free of dirt, loose paint, rust, oil, grease, coal tar, silicone, or other contaminants.
• Apply when temperature is above 5°C (40°F) for black products or 10°C (50°F) and rising for colored products.
• Apply each coat in an alternate direction to the last coat to ensure even coverage.
• Apply final coat in the direction of slope for positive drainage.
• Apply next coat when dry to the touch with nothing wet underneath and is uniform in color.
• Avoid hot, direct, intense sun when applying.
• Avoid contact with solvents and solvent based cleaners, adhesives, and paints.
• Do not allow to freeze until fully cured.
• Do not combine black products with colored products.
• Do not apply in wet conditions (including fog and dew) or if rain is forecasted within 24 hours.
• Wrap brushes in plastic and refrigerate to use for next coat.
• Remove painters tape/blocking while coating is still wet.
• Seal gaps, cracks, etc. with Liquid Rubber caulking (or equivalent).
• Initial cure(set) within 48 hours or until completely dry.
• Curing depends on temperature, humidity and airflow.
• Make sure what you’re coating is at least 5 degrees above the dew point of the environment you are coating in. (See technical specs for more details)
• For best results remove existing paints/coatings and apply directly to the substrate. (Some paints and coatings will not be compatible. Loose/flaky paint may be an indication that the existing paint/coating is not well bonded and therefore your Liquid Rubber solution may fail if applied over it instead of directly to the substrate. Oil based paints, enamels, epoxies, powder coats can be difficult to bond to. Contact your Liquid Rubber technical representative for further direction.)
• It is always a good idea to apply a small test patch in an inconspicuous area to ensure adequate adhesion prior to full application.
 

• Liquid Rubber MetalSafe Sealant Data Sheet
• Liquid Rubber MetalSafe Sealant Safety Data Sheet

You take pride in the condition, appearance, and performance of your property. After all, your home is something you can pass on for generations—it can be part of your lasting legacy
 

It’s our mission to help you fulfill that endeavor, and we’re doing exactly that for countless satisfied customers through our Polyurethane Deck Coating. It’s the hidden ingredient that can preserve your property for decades...

Delivering Pristine Quality You Can Share With Your Family

Here at Liquid Rubber, we understand that quality and performance hold paramount importance. That’s why our polyurethane deck coating is designed to be 10 times stronger than traditional deck coatings.

Our Polyurethane Deck Coating delivers a hard waterproof surface to keep your property in pristine condition, and provides a fiercely durable protective layer to keep your property performing at the highest level.

From family cookouts to fishing adventures with the grandkids, your deck or dock will be a constant source of happiness and everlasting memories for years to come when it’s wearing Liquid Rubber Polyurethane Deck Coating as armor.

Produces a Look You Can Be Proud Of

Quality and performance are absolutely necessary, but we know the appearance of your property matters too. That’s why our Polyurethane Deck Coating comes in various attractive colour and texture options that can be applied to deck boards, plywood, and concrete.

Liquid Rubber Polyurethane Deck Coating gives you a look you will be proud to share with your family, friends, and guests.

Meanwhile, the coating’s waterproof membrane has excellent solar reflectivity and UV stability to enhance appearance and performance. Plus, it’s easy to apply.

Protect your surfaces with Liquid Rubber Polyurethane Deck Coating to preserve your property—and those everlasting memories—for generations.

Tips

• Apply using a 3/8 (10mm) roller, brush or paint sprayer.
• Apply to a clean, dry surface that is free of dirt, silicone, loose paint, rust, oil, grease, coal tar, or other contaminants.
• Apply when temperature is above 10C/50F and rising.
• Use Liquid Rubber Deck and Patio Cleaner to prep wood.
• For extra adhesion, performance and longevity and to create a moisture vapor barrier, use 1 heavy coat of Multi-Purpose Primer.  
• Brush products between deck boards.
• Apply each coat in an alternate direction to the last coat to ensure even coverage.
• Apply final coat in the direction of slope for positive drainage.
• Apply next coat when dry to the touch with nothing wet underneath and is uniform in color. (typically 4-6 hours)
• Avoid hot, direct, intense sun when applying.  Mornings and Evenings are best if it's blistering hot.
• Typically cures within 48-72 hours. (5-7 Days for furniture)
• Avoid contact with solvents and solvent based cleaners, adhesives, and paints.
• Do not allow to freeze.
• Do not combine black products with colored products.
• Curing time depends on temperature, humidity and airflow.
• Do not apply in wet conditions (including fog and dew) or if rain is forecasted within 24 hours.
• Make sure what you’re coating is at least 5 degrees above the dew point of the environment you are coating in. (See technical specs for more details)
• For best results remove existing paints/coatings and apply directly to the substrate. (Some paints and coatings will not be compatible. Loose/flaky paint may be an indication that the existing paint/coating is not well bonded and therefore your Liquid Rubber solution may fail if applied over it instead of directly to the substrate. Oil based paints, enamels, epoxies, powder coats can be difficult to bond to. Contact your Liquid Rubber technical representative for further direction.)
• It is always a good idea to apply a small test patch in an inconspicuous area to ensure adequate adhesion prior to full application.
• Wait 3 days for light foot traffic.
• Wait 5-7 days before placing furniture back on surface.

• Liquid Rubber Polyurethane Deck Coating Application Guideline
• Liquid Rubber Polyurethane Deck Coating Smooth Deck Data Sheet
• Liquid Rubber Polyurethane Deck Coating Textured Deck Data Sheet
• Liquid Rubber Polyurethane Deck Coating Smooth Deck SDS
• Liquid Rubber Polyurethane Deck Coating Textured Deck SDS